How to Set Up Macard N300 Extender?

Macard N300 WiFi extender is one of the router signals repeaters which extend your router’s Wi-Fi network. On this page, you will learn two quick methods explaining Macard N300 WiFi extender setup. Besides, we will also elaborateon errors (like Macard N300 setup not working) and troubleshooting tips to resolve unwanted errors.

WPS Method to Set Up Macard N300 Extender
  1. Step 1: Power on the Macard extender in the vicinity of WiFi Router.

    2. The power LED will blink initially, and turns solid blue once the extender boost up properly.

  2. Step 2: Press the WPS button on the router and then switch on the extender within 1 minute.
    3. wps-method-setup-macard-n300-extender
  3. Step 3: Wait for a few seconds until the extender WPS LED shows solid blue light.

    4. Solid Blue light on the WPS LED means your extender is connected to the router.

  4. Step 4: Unplug the extender and place anywhere in your home , but within the reach of router.
Manual Method to Set up Macard Extender
  1. Step 1: Plug the extender near your router and power it on. And, connect PC or laptop to the extender’s WiFi network.
  2. Step 2: Open browser in your computer and enter the IP address 192.168.10.1 or URL address go.macard.online in the search bar.
  3. Step 3: Login page of the Macard web-based interface will be loaded.
  4. Step 4: Enter the Password mentioned on the extender’s user manual or label.

    5. Usually, the password is “admin”.

    manual-method -to-setup-macard-extender
  5. Step 5: Your extender will search for the local WiFi networks. Select the ones which you want to extend.
  6. Step 6: Enter the username and password for the extended network and click on SAVE button.
    7. manual-method -to-setup-macard-extender-username-password

    Wait for a few seconds until the extender’s Internet LED turns solid blue. It indicates that the configuration of Macard N300 is complete. Now, you can unplug the extender and place anywhere midway between the router and the area with poor WiFi range to enjoy seamless internet connection.

    In case you are facing issues while doing Macard N300 setup then you can identify the key reasons and troubleshoot them.

Macard N300 Setup not working Errors
  • Router and extender are not connected to each other.
  • Extender is not getting enough power supply or facing temporary electricity cuts.
  • Extender is connected to router according to the light but not receiving internet signal.
  • Router and modem’s weak connection can also be reason why N300 device might not be working.
Troubleshoot Macard N300 Setup Not Working Errors
  • Restart N300 extender

    Try restarting Macard N300 setup, by turning it off and on.

  • Check Router and Extender Connection

    Check forconnection errors between router and extender. If WPS method is used for the connection, then bring the extender close to the router and re-do the WPS method. If manual method is used, access the Macard interface on web and check all settings configured.

  • Reconfigure Extender Settings

    Reconfiguration can be helpful if you are facing any problems in Wi-Fi connectivity or low internet speed. To reconfigure, please access Macard web interface using either IP address “192.168.10.1” or URL “go.macard.online” in your computer. Enter login details (username and password) and get to the dashboard, here, you can reset all settings of the extender.

  • Reset the Extender

    Resetting your extender will clear out all previous settings from the device and then again you have to re-do Macard N300 setup from the start. To reset:

    • Get any paper pin or pen.
    • Press and hold the RESET button on the device about 10 seconds.
    • The reset process will start.
    • In a few minutes, you can re-do the setup.