No Internet on Macard WiFi Extender: Need Solutions

The Macard WiFi range extender is a small networking device which you can link to the router wirelessly. But, after the connection what if the extender won’t get the internet. Worry not, this no internet on Macard WiFi extender issue is resolvable.

Here we provide you with common issues and solutions to fix the WiFi extender no internet problem. So, let’s dive in.

Reasons Why There is No Internet on Extender

In this section you find most common reasons why your Macard extender is not connected to internet:

• Faulty power supply to the extender
• The Macard extender not connected with the router
• WiFi Extender setup is incomplete
• Extender facing multiple technical issues
• Need a factory reset

Now, let’s resolve the no internet on Macard WiFi range extender.

Troubleshooting No Internet on Macard WiFi Extender

Below are a few major troubleshooting tips and solutions which are also used by our experts to resolve the similar issues. So, try these tips without hesitation.

Move Extender Close to the WiFi Router

• Use your device – Walk from your router outward while watching the WiFi signal on your phone or laptop. The spot where it starts to drop from full bars? That’s your limit.
• Plug in the extender just before the signal weakens – That’s your sweet spot. Not too close, not too far.
• Check the extender LEDs – Most extenders have light indicators that tell you signal strength. Green = good. Amber = just okay. Red = too far.
• Run a speed test – After moving it, test the speed on both sides near the extender and farther away. If it improved, you’re in business.

Check Errors in Macard Extender Setup

• Plug it directly into a wall outlet, not a power strip. Wait for the power LED. It should turn solid not blinking forever. If the LED never goes solid, the extender isn’t booting correctly. Try a different outlet or reset it.
• Extender can have a buggy firmware. If you got yours recently and it keeps dropping or throws random errors during setup, it could be the firmware acting up. So, update it through the go.macard.online interface.
• Double-check your caps lock. Check if your main router has WPA3-only security mode. Switch your main router to WPA2/WPA3 mixed mode. Also avoid special characters in passwords. Keep it simple till setup completes. You can always change it back later.

Extender Reboot or Power Cycle

Doing a proper reboot or power cycle refreshes everything: Clears cache, Resets signal paths, Fixes dropped IP conflicts, & Kicks out weird bugs. Now, let’s power cycle your extender:

• Unplug the extender from the power outlet.
• Wait for a full 30-60 seconds.
• Plug it back in.
• Give it 1-2 minutes to fully boot up.

Reset Your Range Extender

• Almost every extender has a tiny reset hole. Usually labeled “Reset” or “Factory Reset”. You’ll need that toothpick or paperclip to reach it.
• Make sure your extender is plugged into a live socket and that the power LED is on. You don’t want to reset it during a power blip or blackout.
• Insert your paperclip and press down gently but firmly. You might see the power light start blinking. That means it’s rebooting and clearing all settings.
• Once you release the reset button, give it about 1–2 minutes. The extender will reboot, the lights will cycle, and eventually it’ll settle usually with just the power light on, and no WiFi light.

Reconfigure Macard Extender

• Plug the extender into a wall socket midway between your router and your dead zone.
• On your phone or laptop, connect to the Macard WiFi network.
• Open a browser (Chrome or Safari or any other).
• In the address bar, type: 192.168.10.1. This is the Macard extender’s setup portal.

If the page doesn’t load, double-check you’re connected to the extender’s network. That’s the usual culprit.

Once you’re in, you’ll see the Macard WiFi extender setup page. Enter the default login:
Username: admin
Password: admin

Once logged in:

• Hit the “Repeater” mode or “Wireless Repeater” option.
• The extender will scan for available WiFi networks.
• Pick your main home WiFi (NOT a guest network).
• Enter your WiFi password exactly in case-sensitive.
• Change the extender SSID if you want (or leave it with _EXT at the end).

Ending Thoughts

Hope, your extender is connected to the router again and getting internet signals from it. Now, you can use the internet in the dead WiFi zones as well.

FAQs